terabyte11
diff --git a/‎Output_files/Cyclone_XL/Cycl_XYgearCover_x2.stl
587 KB b/‎Output_files/Cyclone_XL/Cycl_XYgearCover_x2.stl
587 KB
diff --git a/‎Output_files/Cyclone_XL/Cycl_Xcarriage.stl
308 KB b/‎Output_files/Cyclone_XL/Cycl_Xcarriage.stl
308 KB
diff --git a/‎Output_files/Cyclone_XL/Cycl_Xframes.stl
518 KB b/‎Output_files/Cyclone_XL/Cycl_Xframes.stl
518 KB
diff --git a/‎Output_files/Cyclone_XL/Cycl_YbackFrame.stl
124 KB b/‎Output_files/Cyclone_XL/Cycl_YbackFrame.stl
124 KB
diff --git a/‎Output_files/Cyclone_XL/Cycl_Ycarriage_linearBearingHolder_x4.stl
282 KB b/‎Output_files/Cyclone_XL/Cycl_Ycarriage_linearBearingHolder_x4.stl
282 KB
diff --git a/‎Output_files/Cyclone_XL/Cycl_Ycarriage_nutHolder.stl
45 KB b/‎Output_files/Cyclone_XL/Cycl_Ycarriage_nutHolder.stl
45 KB
diff --git a/‎Output_files/Cyclone_XL/Cycl_YfrontFrame.stl
154 KB b/‎Output_files/Cyclone_XL/Cycl_YfrontFrame.stl
154 KB
diff --git a/‎Output_files/Cyclone_XL/Cycl_YrodIdlers.stl
506 KB b/‎Output_files/Cyclone_XL/Cycl_YrodIdlers.stl
506 KB
diff --git a/‎Output_files/Cyclone_XL/Cycl_allGears.stl
905 KB b/‎Output_files/Cyclone_XL/Cycl_allGears.stl
905 KB
diff --git a/‎Output_files/Cyclone_XL/Cycl_rodFixer_x6.stl
256 KB b/‎Output_files/Cyclone_XL/Cycl_rodFixer_x6.stl
256 KB
diff --git a/‎Output_files/Cyclone_XL/Cyclone_XL.png
51 KB b/‎Output_files/Cyclone_XL/Cyclone_XL.png
51 KB
diff --git a/‎Output_files/Cyclone_XL/README.md
+18 b/‎Output_files/Cyclone_XL/README.md
+18
diff --git a/‎Output_files/Cyclone_XL/STL_plates/Cyclone_fullPlate.amf
1.01 MB b/‎Output_files/Cyclone_XL/STL_plates/Cyclone_fullPlate.amf
1.01 MB
diff --git a/‎Output_files/Cyclone_XL/STL_plates/Cyclone_fullPlate.stl
3.74 MB b/‎Output_files/Cyclone_XL/STL_plates/Cyclone_fullPlate.stl
3.74 MB
@@ -0,0 +1,18 @@
+
+Cyclone XL (beta)
+===========================
+
+<p align="center">
+<img src="Cyclone_XL.png" width="80%">
+<div align="center"><i>Cyclone v2.0</i></div>
+</p>
+
+Differences from regular version:  
+- Smooth rod lengths: X=340mm Y=770mm (cut them with some additional margin).  
+- Note that the Y rods (the long ones) must be M10 rather than M8, and the Y linear bearings LM10UU.  
+
+
+Disclaimer  
+--
+This hardware/software is provided "as is", and you use the hardware/software at your own risk. Under no circumstances shall any author be liable for direct, indirect, special, incidental, or consequential damages resulting from the use, misuse, or inability to use this hardware/software, even if the authors have been advised of the possibility of such damages.  
+