0001-port-for-easyarm-imx280a.patch

--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -11,7 +11,7 @@
 
 	memory@40000000 {
 		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
+		reg = <0x40000000 0x04000000>;
 	};
 
 
@@ -107,9 +107,9 @@
 			ssp0: spi@80010000 {
 				compatible = "fsl,imx28-mmc";
 				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
+				pinctrl-0 = <&mmc0_4bit_pins_a
 					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
+				bus-width = <4>;
 				wp-gpios = <&gpio2 12 0>;
 				vmmc-supply = <&reg_vddio_sd0>;
 				status = "okay";
@@ -159,10 +159,11 @@
 					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};
 
-				led_pin_gpio3_5: led_gpio3_5@0 {
+				led_pin_gpios: led_gpios@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
-						MX28_PAD_AUART1_TX__GPIO_3_5
+						MX28_PAD_SSP0_DATA7__GPIO_2_7
+						MX28_PAD_SAIF0_MCLK__GPIO_3_20
 					>;
 					fsl,drive-strength = <MXS_DRIVE_4mA>;
 					fsl,voltage = <MXS_VOLTAGE_HIGH>;
@@ -198,7 +199,7 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_24bit_pins_a
 					     &lcdif_pins_evk>;
-				status = "okay";
+				status = "disabled";
 
 				port {
 					display_out: endpoint {
@@ -237,7 +238,7 @@
 			};
 
 			lradc@80050000 {
-				status = "okay";
+				status = "disabled";
 				fsl,lradc-touchscreen-wires = <4>;
 				fsl,ave-ctrl = <4>;
 				fsl,ave-delay = <2>;
@@ -267,26 +268,26 @@
 
 			pwm: pwm@80064000 {
 				pinctrl-names = "default";
-				pinctrl-0 = <&pwm2_pins_a>;
+				pinctrl-0 = <&pwm4_pins_a>;
 				status = "okay";
 			};
 
 			duart: serial@80074000 {
 				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
+				pinctrl-0 = <&duart_pins_b>;
 				status = "okay";
 			};
 
 			auart0: serial@8006a000 {
 				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
+				pinctrl-0 = <&auart0_2pins_a>;
 				uart-has-rtscts;
 				status = "okay";
 			};
 
-			auart3: serial@80070000 {
+			auart1: serial@8006c000 {
 				pinctrl-names = "default";
-				pinctrl-0 = <&auart3_pins_a>;
+				pinctrl-0 = <&auart1_2pins_a>;
 				status = "okay";
 			};
 
@@ -303,7 +304,7 @@
 	ahb@80080000 {
 		usb0: usb@80080000 {
 			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_id_pins_a>;
+			pinctrl-0 = <&usb0_id_pins_b>;
 			vbus-supply = <&reg_usb0_vbus>;
 			status = "okay";
 		};
@@ -318,7 +319,7 @@
 			pinctrl-names = "default";
 			pinctrl-0 = <&mac0_pins_a>;
 			phy-supply = <&reg_fec_3v3>;
-			phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+			phy-reset-gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
 			phy-reset-duration = <100>;
 			status = "okay";
 		};
@@ -327,13 +328,13 @@
 			phy-mode = "rmii";
 			pinctrl-names = "default";
 			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
+			status = "disabled";
 		};
 	};
 
 	sound {
 		compatible = "fsl,imx28-evk-sgtl5000",
-			     "fsl,mxs-audio-sgtl5000";
+				"fsl,mxs-audio-sgtl5000";
 		model = "imx28-evk-sgtl5000";
 		saif-controllers = <&saif0 &saif1>;
 		audio-codec = <&sgtl5000>;
@@ -342,13 +343,19 @@
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
-		pinctrl-0 = <&led_pin_gpio3_5>;
+		pinctrl-0 = <&led_pin_gpios>;
 
-		user {
-			label = "Heartbeat";
-			gpios = <&gpio3 5 0>;
+		run {
+			label = "led-run";
+			gpios = <&gpio2 7 0>;
 			linux,default-trigger = "heartbeat";
 		};
+
+		err {
+			label = "led-err";
+			gpios = <&gpio3 20 0>;
+			linux,default-trigger = "default-on";
+		};
 	};
 
 	backlight_display: backlight {